Residential · Kansas City, KS
Elite Epoxy Kansas City has served Kansas City since 2018 with epoxy pool deck coating installation and repair for concrete pool surrounds. We fix peeling coatings, scaling concrete, and slick surfaces with moisture-tested prep, crack repair, and UV-stable topcoats built for sun, water, and chemicals.
A pool deck coating is only as good as the slab prep. We start with a site check for spalling, hollow spots, previous paint or acrylic sealers, and control-joint movement, then verify profile and moisture before we coat. Depending on the condition, we diamond-grind or shot-blast to reach a concrete surface profile around CSP 2-3, detail the edges, and clean thoroughly so bond is not compromised. Cracks get routed and filled with a flexible polyurea or epoxy crack filler, pitted areas are skimmed with an epoxy mortar, and joints are re-established so the coating does not bridge active movement.
Kansas City weather swings and pool chemistry are hard on coatings, so we build systems for UV and water exposure, not just garage-floor epoxy. For most epoxy pool deck projects, we use a broadcast texture layer for traction, then lock it in with a UV-stable aliphatic polyaspartic or polyurethane topcoat that resists yellowing and chalking. Slip resistance is tuned with graded silica or polymer grit so it is barefoot-friendly while still helping prevent slips when wet. We also address slope and drainage at transitions, keep coating thickness consistent at steps and coping edges, and use chemical-resistant topcoats where chlorine, salt systems, and sunscreen oils are common.
Customers in Kansas City, KS choose us because we install pool-deck systems like a contractor, not a painter. You get a written scope that lists surface prep, crack and spall repair, broadcast media, and topcoat chemistry, along with a realistic cure and return-to-service schedule. Our crews use professional grinders with HEPA dust control, moisture testing, and batch tracking so the coating goes down at the right temperature and film build. When we repair a failed epoxy pool deck, we focus on the real cause, moisture vapor, poor prep, incompatible layers, or UV exposure, so the fix lasts instead of peeling again next season.
At the end, we walk the deck with you and check uniform texture, edge lines, and coverage around drains, ladders, and step nosings. You receive care guidelines for curing, cleaning (pH-neutral cleaners, soft bristle wash), and what to avoid (acid washes, aggressive pressure tips, de-icing salts on coated areas). We also review expansion joints and how to maintain them so movement does not damage the coating. If you need staged work to keep part of the pool open, we can plan phases around access points and cure times, then leave the site clean and ready for use.
Yes. We carry insurance and provide written estimates that spell out prep, materials, and cure times so you know what you are getting.
Sometimes, but only after proper removal and evaluation. We typically diamond-grind to remove loose coatings and create a fresh profile, then spot-prime and rebuild the system for reliable adhesion.
Yes. We can adjust texture with full flake, quartz, or anti-slip additives like aluminum oxide, balancing traction with cleanability for the space.
It depends on the system, but many installs land in the 15-30+ mil range across base coat(s) and topcoat(s). We recommend the build based on traffic, tires, and chemical exposure.
A properly prepped slab with a quality epoxy base coat and the right topcoat greatly reduces hot-tire pickup. Tire plasticizers, moisture, and inadequate prep are the common causes when it happens.
An epoxy pool deck should do two things well, bond tightly to concrete and stay safe under bare feet when the surface is wet. Elite Epoxy Kansas City installs and repairs epoxy pool deck systems for residential pools, apartment communities, hotels, and fitness facilities, using proper concrete profiling, crack repair, and UV-stable topcoats. Whether your current coating is peeling, fading, or slick, we can rebuild the system so it performs through Kansas City heat, freeze-thaw cycles, and regular pool chemical exposure.
Pool surrounds fail when coatings are applied over weak concrete, old acrylic sealers, or surfaces that were only acid washed. Our process starts with evaluation, then mechanical prep to the right profile, followed by repair of spalls, pop-outs, and random cracks. For resurfacing, we can incorporate epoxy patch mortar to level worn spots, then install a broadcast layer that gives consistent traction across walking zones, steps, and equipment pads.
Because epoxy can amber in direct sun, most outdoor projects finish with an aliphatic polyaspartic or polyurethane clear coat that protects color and improves chemical resistance. We can match the look you want, solid color, light flake, or a textured quartz-style finish, while controlling grit size so the deck stays comfortable. If drainage is an issue, we address low areas and transitions before coating to reduce ponding and premature wear.
If you are comparing contractors for an epoxy pool deck in Kansas City, KS, look for specifics: mechanical prep methods, moisture checks, repair materials, and the exact topcoat chemistry. We provide a written plan, keep surfaces clean with dust-controlled equipment, and verify coverage during the final walkthrough. Contact Elite Epoxy Kansas City to schedule a free written estimate and get a pool deck that looks clean, grips better, and holds up season after season.
Call now or send a request and we will reach out within one business day to schedule your free, no-obligation estimate in Kansas City. We assess the project, review the details, and give you a written quote before any work starts, so you know exactly what to expect.
Prefer to write? Contact us or head back to the home page.
